NetworX™ Series NX-148E LCD Keypad User Manual
NX-148E LCD Keypad 8CANCEL / ABORT FEATURE (Optional, if programmed) The cancel light will flash during an abort delay time. If a code is entered fo
NX-148E LCD Keypad 9If you do not know the number of the zone you wish to bypass, use the following steps: Step 1 Press r • The descripti
NX-148E LCD Keypad 10 Select an Option Press for Help Auxiliary Key - If programmed, you can activate the auxiliary alarm by pressing the Emergency
NX-148E LCD Keypad 11 VIEW ZONE STATUS Step 1 Press r • . The LCD Screen will display the zone status. Step 2 Use the up and down scroll keys
NX-148E LCD Keypad 12 DISPLAY TEST FUNCTION This function will perform a test of the LCD display. No alarms or reports will be sent. Step 1 Press
NX-148E LCD Keypad 13 CHANGING USER CODES Step 1 Press r 5 . The LCD Screen will prompt for a code. Step 2 Enter [master code]. The LCD S
NX-148E LCD Keypad 14 PROMPT Outputs used? DO NOT CHANGE THIS SEGMENT! Open / Close Rprt? Bypass enable? Arm / Disarm? (These are for use b
NX-148E LCD Keypad 15 READING THE EVENT LOG The control panel has an event log that can be retrieved using a master code. This log contains a listin
NX-148E LCD Keypad 16 SETTING THE SYSTEM CLOCK Step 1 Enter r 9 7 . The LCD Screen will prompt for a code. Step 2 Enter [master c
NX-148E LCD Keypad 17 IV. PARTITIONED SYSTEMS OPERATION This system is “ is not “ partitioned. If your system is multi-partitioned and th
NX-148E LCD Keypad 18 This display is reflecting all 8 areas are Ready, and Area 5 is disarmed. NOTE: If a number is flashing on the Armed line, tha
NX-148E LCD Keypad 19 OPERATING INDIVIDUAL AREAS IN THE MULTI-PARTITION MODE Enter a code that is a valid arm/disarm code for the area you wish to
NX-148E LCD Keypad 20 V. KEYPAD CONTROL TONES (BEEPS) A sounder is built into the keypad and may sound for any of the following reasons: Beeps
NX-148E LCD Keypad 21 VI. SERVICE DISPLAY The following message will be displayed periodically if the security system requires service. Call your s
NX-148E LCD Keypad 22 Expansion Aux. comm. fail An auxiliary reporting device has failed to communicate. Expansion Box tamper A box containing an expa
NX-148E LCD Keypad 23 VII. APPENDIX A - EVENT LOG NOTE: Your system may not have all of the features listed in this table. DISPLAY DESCRIPTION TX
NX-148E LCD Keypad 24 DISPLAY DESCRIPTION Cancel Cancel System is disarmed and the Cancel button was pressed within 5 minutes of an alarm. Gnd Flt
NX-148E LCD Keypad 25 VIII. EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition. For
NX-148E LCD KEYPAD FIRE light is “on” to indicate fire alarm, flashes to indicate a trouble condition with your fire system. READY light is “on” w
SYSTEM NOTES
NX-148E LCD Keypad 1TABLE OF CONTENTS I. GLOSSARY OF TERMS...
NX-148E USERS MANUAL NX148EUC05 REV C (June2005)
NX-148E LCD Keypad 2THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF YOUR SE
NX-148E LCD Keypad 3I. GLOSSARY OF TERMS Abort Delay: An option that allows a delay in reporting to the central station. Authority Level: The lev
NX-148E LCD Keypad 4II. UNDERSTANDING THE LIGHTS Armed Light The armed light is “on” when the system is armed. The armed light is “off” when it is
NX-148E LCD Keypad 5III. KEYPAD FUNCTIONS ARMING YOUR SYSTEM IN THE “AWAY” MODE AWAY is utilized when the user is going away from the premise and w
NX-148E LCD Keypad 6ARMING YOUR SYSTEM IN THE “STAY” MODE STAY is utilized when the user is inside the premise and wants protection around the perimet
NX-148E LCD Keypad 7USING THE QUICK ARM The Quick Arm feature may be used if it is enabled. Quick Arm will allow the user to arm the security system
Comentários a estes Manuais